|
RUG
Sept 5, 2006 8:56:59 GMT 10
Post by mudguts on Sept 5, 2006 8:56:59 GMT 10
it's the residue after ya dump a load up j-lo's front bum wands, just a techy term mate, don't sweat it
|
|
seeds
Frankfurt
Posts: 2,324
|
RUG
Sept 5, 2006 9:02:05 GMT 10
Post by seeds on Sept 5, 2006 9:02:05 GMT 10
hotmix- isnt that when it goes off/ cures fast. more part b than normal
|
|
nubby
Frankfurt
Posts: 2,490
|
RUG
Sept 5, 2006 9:10:42 GMT 10
Post by nubby on Sept 5, 2006 9:10:42 GMT 10
thats it seeds!................lards may also be right but i havent met j-lo yet
|
|
seeds
Frankfurt
Posts: 2,324
|
RUG
Sept 5, 2006 9:13:34 GMT 10
Post by seeds on Sept 5, 2006 9:13:34 GMT 10
tell ya wot JLo would be copping the hotmix around the back door while I slapped those buns silly
|
|
|
RUG
Sept 5, 2006 9:19:38 GMT 10
Post by mudguts on Sept 5, 2006 9:19:38 GMT 10
only if she'd been gyrating on stage for a few hours beforehand seeds.....................
mmmmmmmmmmmm, hot sweaty minge!!!!!!!!!!!
|
|
nubby
Frankfurt
Posts: 2,490
|
RUG
Sept 5, 2006 9:21:19 GMT 10
Post by nubby on Sept 5, 2006 9:21:19 GMT 10
wwwwaaahhahahhaahhaaaa!!!! shed be ready wit some custom homemade KY
|
|
seeds
Frankfurt
Posts: 2,324
|
RUG
Sept 5, 2006 9:29:30 GMT 10
Post by seeds on Sept 5, 2006 9:29:30 GMT 10
I lived in Darwin and Townsville for a number of years so I'm used to hot sweaty minge ;D
|
|
|
RUG
Sept 5, 2006 10:03:02 GMT 10
Post by Wands on Sept 5, 2006 10:03:02 GMT 10
ohhh the stench!!!
|
|
|
RUG
Sept 5, 2006 10:11:29 GMT 10
Post by Wands on Sept 5, 2006 10:11:29 GMT 10
So by increasing the amount of catalyst you speed up the gel time but how else does it help??
|
|
seeds
Frankfurt
Posts: 2,324
|
RUG
Sept 5, 2006 10:35:54 GMT 10
Post by seeds on Sept 5, 2006 10:35:54 GMT 10
ya get a betta hit off the fumes
|
|
|
RUG
Sept 5, 2006 10:42:47 GMT 10
Post by mudguts on Sept 5, 2006 10:42:47 GMT 10
and more of dem dere pheromones in da sweaty version = more da moaning too
|
|
Gaz
Frankfurt
Posts: 2,459
|
RUG
Sept 5, 2006 10:51:51 GMT 10
Post by Gaz on Sept 5, 2006 10:51:51 GMT 10
Wands, if you increase the catalyst ratio you will have a faster brew, this also has a doiwnside as the resin/bog will be more brittle and can also casuse minute (as in small not in time) cracks that allow moisture in. Best ratio to mix at for polyester resin is between .75-1.5%Catalyst to total resin. If you want to speed up the cure time you can add promoter to the resin prior to adding catalyst. Be carefull though as promoter and catalyst are not good when mixed together. The result of mixing these two together will be a pretty spectacular explosion!! So if you are intending using promoter, be ready for the terrorist squad to knock on the door.
|
|
|
RUG
Sept 5, 2006 11:01:46 GMT 10
Post by Wands on Sept 5, 2006 11:01:46 GMT 10
ummm... no promoter for me.
Yeah I usually mix at 1% or slightly less.
|
|
|
RUG
Sept 5, 2006 11:02:55 GMT 10
Post by Wands on Sept 5, 2006 11:02:55 GMT 10
hahaha, when i loaded this page up the google ads were advertising rugs and floor coverings.
|
|
nubby
Frankfurt
Posts: 2,490
|
RUG
Sept 5, 2006 11:35:01 GMT 10
Post by nubby on Sept 5, 2006 11:35:01 GMT 10
when ya usin queey ya gots ta hotmix it....fukin shit drips all over and takes forever to set if ya dont......but i dont do it glassin, cause it goes brown and crackly
|
|